Opnext TRF5325ANLB202
Opnext · SFP transceiver, 100BASE-FX · TRF5325ANLB202
what it is
A 100BASE-FX transceiver (Opnext) in the SFP form factor, part number TRF5325ANLB202. Works over two multimode (MM) fibers (duplex), 1310 nm. Reach per manufacturer: 2 km. These properties follow from the part number and the typical specification of this class — there is no manufacturer datasheet. Production year stored in memory: 2007–2008. Revisions seen in the examined units: A1A. The switch reports it as GLC-GE-100FX. Units examined: 3.
what we read from it
The transceiver memory states explicitly that there are no optical diagnostics. The switch reads only its identity and basic signals (loss of signal, transmitter fault), without temperature, power or laser current.
A full read of the transceiver memory gives it a diagnostics score of 3 out of 15 — counted are: presence of measurements, manufacturer thresholds, alarm flags set by the transceiver itself and software loss-of-signal indication.
what the transceiver memory declares
Transceiver memory read directly from a Cisco switch (show idprom, page A0) — 3 units. Each item gives the memory byte and value it comes from; we do not show serial numbers, exact dates or the vendor-reserved area.
- Module type: SFP/SFP+ (byte 0 = 0x03).
- Connector: LC (byte 2 = 0x07).
- Standard (compliance code): not declared (bytes 3, 6 = 0x00, 0x00).
- Nominal rate: 100 MBd (byte 12 = 0x01).
- Reach per fiber type: OM2 2000 m, OM1 2000 m (bytes 14-19 = 0x00 0x00 0xC8 0xC8 0x00 0x00).
- Wavelength: field not filled (bytes 60-61 = 0x00 0x00).
- Hardware signals: loss of signal (RX_LOS), transmitter fault (TX_FAULT), transmitter disable (TX_DISABLE) (byte 65 = 0x1A).
- Optical diagnostics (DDM): not declared (byte 92 = 0x00).
- Extended options: none (byte 93 = 0x00).
- SFF-8472 diagnostics revision: not declared (byte 94 = 0x00).
- Chip vendor identifier (OUI): filled (bytes 37-39).
- Memory checksums: valid (bytes 63 and 95).
- Vendor-reserved area: present (bytes 96-127).
- Vendor alarm thresholds: not shown — transceiver does not declare diagnostics.
- Production year stored in memory: 2007–2008.
A declaration in memory is not the same as a reading: none of the switches examined showed diagnostic measurements (Cisco WS-C3750X-12S-S).
how we checked
The result depends on what the transceiver was read with — the same switch model in a different installation can show different data. That is why each reading is recorded separately:
- Cisco Catalyst 3750-X 12S-S (Cisco WS-C3750X-12S-S), firmware
15.2(4)E10— transceiver memory and diagnostics table read from the console, 2026-10-17: diagnostics not shown (3 units). Visible data: loss of signal indication (RX_LOS), transmitter fault indication (TX_FAULT), transmitter disable (TX_DISABLE), manufacturing date, reach per fiber type, standard (compliance code), chip vendor identifier, memory checksums, identity (manufacturer, part number, serial number, revision). Cable test: not tested.
The same transceiver in other switches and a comparison with other models: what each device shows.
what we cannot read
- Temperature, optical power and laser current.
parameters the transceiver returns
The list shows WHAT the device exposes — including parameters we do not use ourselves. There are no values here at all: it is a catalog of capabilities, not a reading from anyone's network. It is not a closed list either — explanation below the table.
12 parameters
| parameter | type |
|---|---|
data_produkcji | date |
numer_czesci | text — part number (PN) |
numer_seryjny | text |
oui_producenta | text — chip vendor identifier |
producent | text — vendor name from transceiver memory |
rewizja | text |
sumy_kontrolne | boolean — transceiver memory validity |
usterka_nadajnika_tx_fault | boolean |
utrata_swiatla_rx_los | boolean |
wylaczenie_nadajnika_tx_disable | boolean |
zasiegi_wlokien | numbers (m / km) for OM1–OM3 and single-mode fiber |
zgodnosc | text — standard (e.g. 1000BASE-LX) |
This is not a closed list. It comes from reading a unit we had access to — it shows what we managed to retrieve, not everything the device can return. A different firmware version, hardware variant or reading path can expose fields that are not here. If you are interested in a specific unit and a specific value — please ask; there is a good chance it can be obtained, even if you do not see it below.
List source: reading of 3 working units (as of 2026-10-19). The list is the sum of what we observed — more units reveal more parameters, so numbers for different models are not directly comparable.